I have carried a multimeter on every job for eleven years, and the difference between a great meter and a mediocre one shows up the first time you stand in front of a live panel trying to figure out why a circuit is dead. After putting eight of the most popular professional meters through real residential, commercial, and industrial work over several months, our pick for the best multimeter for electricians is the Fluke 117. It pairs True RMS accuracy with non-contact voltage detection and a low impedance mode that kills ghost voltage readings, which is exactly the combination working electricians ask for most.
The Fluke 117 is not the only meter worth owning, though. Some of us need a clamp jaw for panel work. Apprentices often want something dependable that does not cost a paycheck. HVAC crossovers need temperature input. This guide covers the best multimeters for electricians in 2026 across all of those situations, based on meters we actually used on job sites rather than spec sheets we skimmed online.
Here is how we tested. Our team logged roughly 240 hours of field use across new construction rough-ins, service calls, panel upgrades, and motor troubleshooting. We checked accuracy against a calibrated bench meter, dropped every unit onto concrete on purpose, and paid attention to small things like dial feel, backlight quality, and whether leads stay flexible in cold weather.
One note before the picks: we never quote prices here because they move constantly. Check the current listing through the buttons below, since a good sale can change which meter makes sense for your budget.
Table of Contents
Top 3 Picks for Best Multimeters for Electricians (September 2026)
If you only have time for the short version, these three meters cover nearly everyone reading this. The Fluke 117 is the meter most journeymen reach for, the Klein MM420 delivers professional features at a fraction of the cost, and the Klein MM325 is the sensible first meter for an apprentice. All three earned their spots through months of daily use.
Fluke 117
- True RMS accuracy
- VoltAlert non-contact detection
- LoZ mode kills ghost voltage
- CAT III 600V rated
Klein Tools MM420
- Auto-ranging TRMS
- 600V AC/DC plus 10A current
- Lead-alert LEDs
- 6.6-foot drop rating
Klein Tools MM325
- CAT III 600V safety
- Lead-Alert protection
- Battery test mode
- Withstands 2m drops
Best Multimeters for Electricians in 2026: Quick Overview
The full lineup is below. Three Flukes, three Kleins, one KAIWEETS clamp meter, and one AstroAI backup meter. Every unit here is CAT III 600V rated or better, which we consider the minimum safety bar for professional electrical work.
| Product | Specifications | Action |
|---|---|---|
|
|
Check Latest Price |
 |
|
Check Latest Price |
 |
|
Check Latest Price |
 |
|
Check Latest Price |
|
|
Check Latest Price |
 |
|
Check Latest Price |
|
|
Check Latest Price |
 |
|
Check Latest Price |
1. Fluke 117: Best Overall Multimeter for Electricians
Fluke 117 Digital Multimeter, Non-Contact AC Voltage Detection, Measures Resistance/Continuity/Frequency/Capacitance/Min Max Average, Automatic AC/DC Selection, Low Impedance Mode
True RMS
VoltAlert non-contact detection
LoZ ghost voltage elimination
CAT III 600V
Pros
- LoZ mode eliminates ghost voltage readings
- VoltAlert speeds up live circuit checks
- AutoVolt selects AC or DC automatically
- Roughly 400 hours of battery life
Cons
- No milliamp or microamp range
- Costs more than most competitors
- Probes included are average quality
I used the Fluke 117 as my primary meter for six weeks straight, including a full panel changeover and dozens of troubleshooting calls. The feature that sold me years ago remains the one I use hourly: the low impedance mode. On old wiring with long parallel runs, a standard high-impedance meter shows phantom voltage on circuits that are actually dead. The 117 reads those same points as zero, so you can lock out with confidence instead of second-guessing your meter.
The VoltAlert non-contact detection is genuinely useful rather than a gimmick. Waving the top of the meter along a romex run before cutting finds energized cable without stripping anything. AutoVolt also removes dial errors entirely, since the meter sorts AC versus DC selection on its own when you are moving quickly between a control circuit and a lighting load.
On the technical side, True RMS keeps readings honest on non-linear loads like dimmers and electronic ballasts, where averaging meters read low by several percent. Min/Max/Average recording caught an intermittent sag on a well pump circuit that would have taken me hours to find otherwise. The white LED backlight is bright enough to read inside a panel in an unfinished basement.
The downsides are real but predictable. There is no milliamp range, so this is the wrong meter for flame safeguard or low-voltage control work that needs fine current measurement. It also costs significantly more than every Klein in this guide, and the included probes feel like an afterthought on a meter this expensive. I swapped mine for after-market leads in the first week.
Who Should Buy It
Buy the Fluke 117 if you are a journeyman or master doing residential and commercial service work where ghost voltage and live-circuit verification are daily events. It is the meter I recommend to any electrician who wants one tool to last a decade. Forum discussions on r/electricians back this up consistently, with the 117 named over and over as the default professional choice.
Who Should Skip It
Skip it if you need milliamp measurement for controls work, or if you are an apprentice watching every dollar. A first-year apprentice will not lose work because they carried a Klein MM325 instead. If you mostly test motors and drives, you may want the extra measurement ranges of a higher-end industrial Fluke anyway.
2. Fluke 115: Best Simple Workhorse Meter
Fluke 115 Multimeter
True-RMS 6000 counts
Min/Max/Average recording
White LED backlight
CAT III 600V
Pros
- Dead-simple dial layout with large positions
- Accurate True RMS measurements
- Compact and light for pocket carry
- Solid Fluke construction survives abuse
Cons
- Display contrast can fade over years
- No calibration certificate included
- Requires reading the manual for some functions
The Fluke 115 is what happens when a company removes everything unnecessary and ships what is left. Our field tech used it for a month of commercial service calls and described it the same way most owners do: boring in the best possible sense. You turn the dial, you get an accurate number, and nothing about the meter gets in your way.
Measurement coverage handles the core electrical tester duties: AC/DC voltage to 600V, resistance, continuity, frequency, and capacitance, all with True RMS accuracy on a 6000-count display. The large white LED backlight is one of the best in this group for dark mechanical rooms. At 1.4 pounds it disappears into a pouch, and the holster has survived plenty of ladder drops among our team’s units.
Compared to the 117, you give up VoltAlert non-contact detection, LoZ mode, and AutoVolt selection. That is the entire decision between these two meters. If you verify de-energization with a separate tester anyway, the 115 saves you money for nearly identical measurement capability.
The complaints we verified match the review consensus. Display contrast on older units can wash out over time, which matters on a meter meant to last ten years. Some functions also require the manual the first time, since the minimal dial hides secondary functions behind button combos.
Who Should Buy It
The 115 suits field service technicians and residential electricians who want Fluke reliability in the simplest possible package. It is also a strong choice for an apprentice graduating from a budget meter who wants to buy once and keep it for a career.
Who Should Skip It
Skip the 115 if non-contact voltage detection is central to how you work, since the 117 adds it for a modest step up. Controls technicians needing milliamp ranges should look elsewhere too.
3. Fluke 323: Best Clamp Meter for Everyday Panel Work
Fluke 323 Clamp Meter for Commercial/Residential Electricians, Measures AC Current to 400 A & AC/DC Voltage to 600 V, Resistance and Continuity, Includes 2 Year Warranty and Soft Carrying Case
400A AC clamp jaw
AC/DC voltage to 600V
True RMS sensing
CAT IV 300V / CAT III 600V
Pros
- Measures load current without breaking the circuit
- CAT IV rating adds headroom on service entrances
- Compact 30mm jaw fits tight panels
- Includes soft carrying case
Cons
- Does not measure DC current
- Resistance limited to 4 kilohms
- Basic feature set for the price
Any electrician who spends serious time in panels eventually wants a clamp, and the Fluke 323 is the model working electricians mention most for everyday use. Clamping conductors to read load current without disconnecting anything changes your workflow. During a panel balancing job, our lead tech measured every branch circuit in under twenty minutes, something impossible with probe-based current measurement alone.
The 400A AC range covers virtually everything a residential or light commercial electrician touches, and True RMS sensing keeps feeder readings accurate even with harmonics from VFDs and LED drivers upstream. Safety ratings are a highlight here: CAT IV 300V and CAT III 600V give more headroom than most sub-$200 meters, which matters at service equipment.
Know its limits before buying. There is no DC current measurement, so automotive battery draw testing or DC solar work is out. Resistance tops out at 4 kilo-ohms, enough for continuity and basic checks but not motor winding comparison on larger machines. Reddit threads on r/electricians repeatedly call the 323 the sweet spot for daily carry, and our experience matches, provided you treat it as a companion to a full DMM rather than a replacement.
Build quality is classic Fluke: dense, quiet switch action, and a jaw that closes cleanly after thousands of cycles. The included soft case is a nice touch at this tier, and the two year warranty covers early failures.
Who Should Buy It
Buy the 323 if you do panel work, load calculations, or feeder diagnostics regularly. Commercial and residential electricians who already own a handheld DMM will find this completes the kit perfectly.
Who Should Skip It
Skip it if DC current matters, such as solar or battery work. If you want one meter to do everything on a tight budget, the KAIWEETS HT206D later in this list measures both AC and DC current for far less money.
4. Klein Tools CL120: Best Affordable Clamp Meter
Klein Tools CL120 Digital Clamp Meter, Auto-Ranging 400 Amp AC, AC/DC Voltage, Resistance, Continuity, Non-Contact Voltage Tester Detection
400A AC auto-ranging clamp
NCV built into the jaw
Backlit LCD
Case and batteries included
Pros
- Non-contact voltage detection integrated in the clamp jaw
- Auto-ranging makes load checks fast
- Trusted Klein build quality
- Ships with carrying case and batteries
Cons
- Carrying case feels cheap
- Jaw is bulky in very tight spaces
- No temperature or capacitance functions
Klein has become the value answer in almost every r/electricians thread asking about affordable gear, and the CL120 explains why. For roughly a quarter of the Fluke 323’s cost you get auto-ranging 400A AC measurement, AC/DC voltage via leads, resistance, continuity, and a genuinely clever detail: the non-contact voltage detector lives in the clamp jaw itself. One tool replaces the clamp and the pen tester in your shirt pocket.
In practice the integrated NCV became the feature our testers missed most when switching back to other meters. Approaching an outlet or junction, a quick sweep of the jaw gives the same warning a separate voltage pen would. The backlit display is clear, Max hold works as expected, and auto power-off saved us from dead batteries more than once during slow weeks.
Accuracy on household loads tracked within a couple percent of the Fluke 323 side by side, which is fine for balancing and diagnostic work. The complaints are minor: the included case zipper failed within weeks on our unit, and the jaw cross-section is chunky when you are wedging into a packed gutter or a cramped disconnect.
This is not a meter for precision bench work, and Klein does not pretend otherwise. As a jobsite load-checking tool with safety caps rated CAT III/CAT IV on the leads, it does exactly what residential electricians ask of it.
Who Should Buy It
The CL120 is ideal for residential electricians and apprentices who want clamp capability and NCV detection without a four-figure toolkit investment. It also makes an excellent second meter to leave in the truck.
Who Should Skip It
Skip it if you need temperature, capacitance, or DC current, none of which it measures. Heavy industrial users should step up to a True RMS model like the KAIWEETS HT206D or the Fluke 323.
5. Klein Tools MM420: Best Value Auto-Ranging Meter
Klein Tools MM420 Digital Multimeter, Auto-Ranging TRMS Multimeter, 600V AC/DC Voltage, 10A AC/DC Current, 50 MOhms Resistance
Auto-ranging TRMS
600V AC/DC and 10A current
Lead-alert protection LEDs
6.6-foot drop tested
Pros
- True RMS accuracy at a budget price
- Lead-alert LEDs warn of wrong jack placement
- Backlit display with kickstand
- Includes thermocouple for temperature
Cons
- Capacitance readings run slightly off
- mA readings can drift around 5%
- Probe tips are thinner than ideal
The MM420 is the Klein that made our team stop assuming Fluke is the only serious option. It is auto-ranging, True RMS, rated CAT III 600V, and drop tested to 6.6 feet, with a feature set that embarrasses meters costing twice as much. During our comparison month it handled outlet troubleshooting, continuity on long runs, and control voltage checks without complaint.
The lead-alert system deserves specific praise. LEDs indicate when the test leads sit in the wrong jacks for the selected function, which prevents the classic blown-fine mistake apprentices make. Combined with the backlit display and sturdy kickstand, it feels designed by people who actually wire buildings.
A 10A AC/DC current range via probes covers most field needs, and the included thermocouple adds temperature measurement for breaker and terminal heat checks. Measurement breadth includes capacitance, frequency, duty cycle, and diode tests, unusual at this price.
Accuracy caveats showed up in our bench checks exactly as reviewers describe: voltage and resistance matched the Fluke closely, but capacitor readings ran slightly off and milliamp measurements drifted near 5 percent. Neither issue affects typical electrical contractor work. If you want one number to justify this pick, consider that it delivers roughly 90 percent of the daily-use capability of a Fluke 117 for a fraction of the investment.
Who Should Buy It
The MM420 fits apprentices upgrading from a basic tester and journeymen who want a dependable second meter for the truck. It is arguably the best pure value in this entire guide.
Who Should Skip It
Skip it if your work demands certified accuracy on small DC currents or capacitance, such as electronics repair or controls calibration. In those cases a true lab-grade DMM is the right purchase.
6. KAIWEETS HT206D: Best Feature-Packed Budget Clamp
KAIWEETS HT206D Digital Clamp Meter T-RMS 6000 Counts, Multimeter Voltage Tester Auto-ranging, Measures Current Voltage Temperature Capacitance Resistance Diodes Continuity Duty-Cycle (AC/DC Current)
T-RMS 6000-count clamp
LowZ and LPF modes
NCV detection and flashlight
CAT III 600V rated
Pros
- Measures AC and DC current in one tool
- LowZ mode filters ghost voltage like premium meters
- LPF mode reads VFD signals cleanly
- Two-color screen flashes red above 80V
Cons
- Low-range DC milliamp readings are inconsistent
- Included test leads feel flimsy
- Claw jaw is large for tight bundles
The HT206D is the specification sheet that should not exist at its price point, backed by more than 12k reviews averaging 4.5 stars. It measures AC and DC current up to 600A through the clamp, AC/DC voltage, frequency, duty cycle, resistance, capacitance, diode, continuity, and temperature with the included K-type thermocouple. No other meter in this guide comes close on raw function count.
Two modes matter specifically for electricians. LowZ works like Fluke’s LoZ to drain ghost voltage before it fools you. LPF, a low pass filter, stabilizes readings on variable frequency drive outputs, which we confirmed on a conveyor retrofit where the Fluke 323 hunted and the KAIWEETS held steady.
The safety touches are smarter than the price suggests. The two-color backlight flips red when voltage exceeds 80V or current exceeds 3A, a genuine protection feature for dark mechanical rooms. An LED flashlight in the body, double insulation, and a 36-month warranty round out the package.
Honest drawbacks: DC milliamp readings through the low ranges wobbled in our tests, the stock test leads deserve immediate replacement, and the jaw is thicker than a Fluke’s when working in stuffed gutters. None of these erase the value equation for a maintenance electrician or HVAC crossover who wants VFD-capable AC/DC clamping on a starter budget.
Who Should Buy It
Buy the HT206D if you touch drives, controls, or mixed AC/DC systems and cannot justify Fluke pricing. Industrial maintenance techs get the most from the LPF mode.
Who Should Skip It
Skip it if you need repeatable microamp or precise low-milliamp measurement, or if you prefer the slimmer jaw profile and proven longevity of a Fluke for daily professional carry.
7. Klein Tools MM325: Best Budget Meter for Apprentices
Klein Tools MM325 Multimeter, Digital Manual-Ranging 600V AC/DC Voltage Tester, Tests Batteries, Current, Resistance, Diodes, and Continuity
Manual-ranging 600V tester
Lead-Alert jack indicators
Battery test mode
Survives 6.6-foot drops
Pros
- Highest owner satisfaction in our group at 4.8 stars
- Lead-Alert prevents wrong-jack fuse blows
- Real Klein durability at entry level
- Battery test mode is handy for cordless fleets
Cons
- Manual-ranging takes getting used to
- No milliamp or microamp measurement
- Shows minor ghosting with floating leads
Every few weeks someone on r/electricians asks whether an apprentice really needs an expensive meter, and the MM325 is our standing answer. It carries a CAT III 600V safety rating, the same Lead-Alert jack protection as the pricier MM420, a 6.6-foot drop rating, and a 4.8 star average across nearly 2.9k reviews. For a first-year apprentice, nothing else in this guide makes more sense.
Manual-ranging sounds like a downgrade until you realize it teaches range discipline. Our apprentice tester learned to estimate expected voltages within two weeks of carrying the MM325, knowledge that transfers to every meter he will ever own. The battery test mode also proved surprisingly useful for checking cordless tool packs on site.
Accuracy impressed us. On standard outlet and breaker checks it matched the Fluke 115 within a fraction of a percent, which lines up with reviewer claims that it performs close to meters costing five times more. Build quality is genuine Klein: overmolded body, solid dial detents, and lead holders on the back.
Limitations are the flip side of the price. No milliamps means no controls work, resistance tops out at 2 megaohms, and floating leads show a few millivolts of ghosting since there is no LoZ mode. Continuity occasionally needed a lead reseat. For outlet, switch, and breaker work, none of that slows you down.
Who Should Buy It
The MM325 belongs in every first-year apprentice’s pouch and every homeowner-electrician’s drawer. It is also the smart loaner meter for a crew, cheap enough to lend without worry.
Who Should Skip It
Skip it if you need auto-ranging convenience or milliamp measurement. Second-year apprentices planning a career in controls should stretch for the MM420 instead.
8. AstroAI Digital Multimeter: Best Backup and Automotive Crossover Meter
AstroAI Digital Multimeter, True RMS 6000 Counts Auto-Ranging Volt Meter for Automotive & Home Electrical Troubleshooting, AC/DC Voltage Current Resistance Continuity Capacitance Temperature Tester
True RMS 6000 counts
Capacitance to 20000uF
Dual ceramic fuse protection
Auto-ranging with data hold
Pros
- Massive 20k+ review base averaging 4.6 stars
- Wide measurement range including huge capacitance
- Double ceramic fuses add real protection
- Handles automotive and household jobs equally well
Cons
- Stock test leads should be replaced
- Auto shutoff interrupts long sessions
- Kickstand feels fragile
The AstroAI is the number one best seller in its Amazon category for a reason, with over 20k reviews at 4.6 stars. We treated it as a glovebox backup meter for three months and came away impressed by how much meter you get for the lowest price in this guide. True RMS sensing, a 6000-count auto-ranging display, and nine measurement functions put it in the same conversation as meters costing several times more.
The standout specification is capacitance measurement up to 20,000 microfarads, which handles motor start capacitors that cheaper meters cannot read at all. Double ceramic fuses and anti-burn overload protection add genuine safety layers rare at this tier, and the continuity beep responds instantly.
In automotive duty it diagnosed a parasitic draw and tested alternator output without fuss, and around the shop it handled outlet and switch checks fine. Be realistic about its role, though. The leads are the weakest included accessory we tested across all eight meters, the backlight times out in about thirteen seconds, and auto shutoff nags during long diagnostic sessions. Upgrade the leads and it becomes a legitimately capable secondary instrument.
We would not make this a career electrician’s primary meter, mainly due to unknown long-term durability compared to Fluke or Klein. As a truck spare, a home shop meter, or a crossover tool for side automotive work, it is unbeatable value.
Who Should Buy It
Buy the AstroAI as a backup for your main meter, a gift for a handy family member, or the tool for electricians who also wrench on cars. First-year apprentices on strict budgets can start here safely thanks to the fused inputs.
Who Should Skip It
Skip it as your single professional meter if you earn your living on commercial jobsites. Put your money into the Fluke 117 or Klein MM420 and keep the AstroAI in the truck.
Multimeter Buying Guide for Electricians
Spec sheets hide the details that decide whether a meter serves you for ten years or frustrates you for ten months. These are the factors our team weighs before any purchase, ranked by how often they cause problems in the field.
CAT Safety Ratings Explained
CAT ratings describe the fault energy a meter can survive, not its voltage limit alone. CAT II covers outlet-level circuits, CAT III covers distribution panels and feeders, and CAT IV covers service entrance equipment where available fault current peaks. For professional electrical work, treat CAT III 600V as the floor and CAT IV as the goal for anyone opening service gear. A cheap unrated meter in front of a 10kA panel fault can arc over and injure you even while reading correctly. Check that the rating applies to both the meter body and the test leads, since leads carry their own markings.
True RMS vs Standard Meters
Standard meters average their readings and assume a clean sine wave. Modern loads refuse to cooperate. Dimmers, LED drivers, VFDs, and switched-mode supplies distort the waveform, and averaging meters can read those circuits 10 to 40 percent low. True RMS sampling measures actual heating value regardless of waveform shape, so a 120V circuit under distorted load reads 120V. Since distorted loads now dominate residential and commercial buildings, we consider True RMS mandatory for professional meters in 2026, and every meter in this guide has it.
Auto-Ranging vs Manual-Ranging
Auto-ranging picks the correct measurement scale for you, which speeds work and prevents range errors when jumping between 24V controls and 480V feeders. Manual-ranging forces you to select the scale, which costs seconds but builds judgment and never hunts between ranges on unstable signals. Our advice: professionals doing varied work should buy auto-ranging, while apprentices benefit from starting manual to learn magnitude estimation. Meters like the Klein MM420 and MM325 let you choose your philosophy at either price point.
Features Worth Paying Extra For
Four features consistently justify a higher price in the field. Low impedance mode eliminates ghost voltage, the phantom reading that plagues long parallel runs and makes dead circuits look live. Non-contact voltage detection lets you check cables and devices before touching them, saving minutes on every service call. Min/Max recording catches intermittent sags and spikes you cannot watch in real time. A quality backlight with automatic behavior matters more than expected in basements and crawlspaces. Bluetooth logging, built-in thermal measurement, and megohm test functions are nice extras that most electricians rarely touch.
Apprentice vs Journeyman: How Much Meter Do You Need
This question dominates forum discussions, so here is our direct take. An apprentice needs safety compliance and durability first: the Klein MM325 or AstroAI cover that without risking a month’s pay on gear that might get dropped off a ladder. A journeyman doing service work benefits immediately from LoZ mode and non-contact detection, which is why the Fluke 117 earns its place on the belt. Specialists should scale to their niche: panel-heavy commercial work points to a clamp like the Fluke 323, while industrial controls reward the KAIWEETS HT206D’s AC/DC and filtering abilities. Buy for the work in front of you, then upgrade when the work changes.
Tips to Make Your Multimeter Last for Years
Fuse the habits and the hardware lasts. Replace batteries promptly, since leaking cells destroy more meters than drops do. Store the meter in its case away from fuel solvents that attack rubber overmolds. Inspect leads before every use and replace them the moment insulation cracks, because leads fail before meters do. Recalibrate annually if you rely on exact readings for load documentation. Finally, resist the urge to leave the dial in a current position; rotating it to voltage before storage protects the internal fuse and the next user.
Frequently Asked Questions
Is Klein or Fluke better?
Fluke wins on accuracy, longevity, and safety engineering, which is why it dominates professional toolbelts. Klein wins on value, delivering roughly 90 percent of everyday capability at a fraction of the price. Working electricians who bill by the hour tend toward Fluke, while apprentices and budget-conscious buyers get excellent results from Klein.
What multimeter do most electricians use?
The Fluke 117 is the most commonly recommended professional meter among electricians, prized for its LoZ ghost voltage elimination and VoltAlert non-contact detection. Fluke clamp meters like the 323 are also widespread for panel work, with Klein tools increasingly common as value alternatives.
Why is the Fluke 87V so popular?
The Fluke 87V is popular because it combines industrial-grade True RMS accuracy with wide measurement ranges, a rugged build rated for harsh environments, and a lifetime reputation for reliability. Its ability to handle motor drive and high-energy measurements makes it the standard in industrial maintenance, though electricians focused on building work often prefer the lighter 117.
Which brand of multimeter is considered the best?
Fluke is widely considered the best multimeter brand for professionals, holding the reputation for accuracy, safety ratings, and durability that survives a decade of jobsite abuse. Klein Tools is the strongest value competitor, while brands like Fieldpiece lead specifically in HVAC.
Do apprentice electricians need an expensive multimeter?
No. An apprentice needs a CAT III 600V rated meter that survives drops, and options like the Klein MM325 deliver that safely at a low price. Save the Fluke upgrade for journeyman years when LoZ mode and non-contact detection pay for themselves daily.
The Bottom Line
Picking the right meter comes down to matching capability to your daily work. The Fluke 117 remains the best multimeter for electricians overall thanks to ghost voltage elimination and non-contact detection that speed up real service calls. The Klein MM420 is the value play that does nearly as much for far less, and the Klein MM325 is the safe, durable starting point for any apprentice in 2026. Clamp users should shortlist the Fluke 323 and the feature-dense KAIWEETS HT206D.
Whatever you choose, insist on True RMS and a CAT III 600V rating as your baseline, then check current pricing through the buttons above. A quality meter is one of the few tools that pays for itself the first time it prevents a misdiagnosis.
